Mitsubishi E Variable frequency drive (VFD) Instruction Manual – Free ebook download as PDF File .pdf), Text File .txt) or read book online for free. Thank you for choosing this Mitsubishi Inverter. This Instruction Manual provides instructions for advanced use of the FR-E series inverters. Incorrect. 10 Jan Thank you for choosing this Mitsubishi Inverter. This Instruction Manual ( basic) is intended for users who “just want to run the inverter”.
|Published (Last):||4 November 2012|
|PDF File Size:||13.24 Mb|
|ePub File Size:||18.34 Mb|
|Price:||Free* [*Free Regsitration Required]|
FR-E EC 5 – Protective function will not activate if an earth ground fault occurs during operation. The other models are designed for harmonic and surge suppression: Jog operation signal timing chart frequency Forward rotation Pr. Initial Value Change List Pr. For power factor improvement, install a reactor on the inverter input mmanual or in the DC mitsubishi e700 vfd manual.
When “2” is set in Pr.
Page The motor speed fluctuation at load fluctuation can be adjusted using Pr. One mitsubishi e700 vfd manual can be assigned to two or more terminals. Pull the cover in the direction of arrow. Page – Current average value monitor signal Pr If the values mitsubishi e700 vfd manual be displayed have five digits or more including decimal places, the fifth or later numerals can not be displayed nor set.
In this case, setting must also be made on the inverter according to the computer. Bold frame indicates stop-on-contact control is valid. Page Output frequency is 3Hz or less Carrier frequency Pr. Forward rotation Example 1: PU signal output, assign the function by setting “10 source logic or sink logic ” in any of Pr.
Mitsubishi FR-E700 2.2kW 230V 1ph to 3ph – AC Inverter Drive Speed Controller
Page Monitor display and monitor output signals Parameter Display set frequency during stop Pr. The monitored digits in 1 increments are displayed as mitsubishi e700 vfd manual are. Page You can find a detailed description of the operation panel with examples in section 4.
Output frequency mitsubishi e700 vfd manual 3Hz or less Carrier frequency Pr. NOTE The wiring length of the terminal 10, 2, 5 should be 30m maximum. While vtd voltage stall oL stops the output frequency during deceleration, the regenera- tion avoidance function is always on and increases the frequency according to the regenera- tion amount.
RS communication with the PU connector.
MITSUBISHI ELECTRIC FR-E INSTRUCTION MANUAL Pdf Download.
Check first when you mitsubishi e700 vfd manual troubles Troubleshooting 7. Please make setting after confirming the function of each terminal.
Parameters mihsubishi not cleared when “1” is set in Pr. Peripheral Devices When the breaker on the inverter primary side trips, check for the wiring fault short circuitdamage to internal parts of the inverter, etc. Monitor display and monitor output signals Parameter 6. Refer to section 3.
Mitsubishi Electric FR-E700 Instruction Manual
This can be used as mitsubishi e700 vfd manual guideline for the maintenance time of peripheral devices. Signal output time for the maintenance output value Maintenance timer value IE Note that the output time range is 2 to 9s, and it is 2s when Pr.
Make setting after confirming the function of each terminal. Motor brake and stop operation Parameter When a high power factor converter FR-HC is used and automatic mitsubishi e700 vfd manual after instan- taneous power failure function is made valid. Mitwubishi For write, set the data as mitsubishi e700 vfd manual control input instruction.
Error Code Invalid data has been mxnual for parameter write, fre- Instruction code error quency setting, etc. Page Special operation Parameter Limit regeneration avoidance operation frequency Pr. Limit the output frequency Parameter 6. Avoid connecting the terminal PC and 5 and the terminal SE and 5.
In addition, negative logic mankal be set on when the inverter is normal, off when the fault oc- curs. Page Since the Pr. Remove the front cover 1 by pulling it toward you in the direction of arrow. Frequency setting by external terminals Parameter Frequency setting by external terminals Refer to Purpose Parameters that must be set Section Make frequency setting by combina- Multi-speed operation Pr.
You can find a detailed description of mitsubishi e700 vfd manual operation panel with examples in section vgd. For the terminal used for REX signal input, set “8” in any of Pr.
When C1 is used to calibrate the full meter deflection in this mode a value of “” is displayed.
Page RES signal or by switching power off. Page Manuql prevention operation during acceleration may increase the acceleration time. After the inverter has started up in the network operation mode, parameter write and operation can be performed from manhal program. Safety Instructions Thank you for choosing this Mitsubishi inverter. PU operation mode Basic settings Change the acceleration time using Pr. Page Frequency setting by external mitsubishi e700 vfd manual Parameter Remote setting function When using the remote setting function, following frequencies can be compensated to mitsubishi e700 vfd manual fre- quency set by RH and RM operation according to the operation mode.